Tank Lining

Sam Tankguard Epoxy 65

A high-build, Two-component, Phenolic Polyamine-cured epoxy coat with excellent
anticorrosive and chemical resistance properties.


Characteristics
• Excellent abrasion and impact resistance.
• Excellent Chemical resistance against Acidic and alkali media.
• Designed to be used in Tank lining in oil& gas and fertilizers plants.
• Excellent hydrocarbon and fuel resistance.
• Designed to Resist dry heat up to 200C°
• Designed to be used under Insulation.
• Compatible with well-designed cathodic protection system.


Physical properties.
Colour Grey, (specific colours)
Texture Egg shell


Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.3 g/ml
Volume solids 65±2% Tested acc. ASTM D 2369
VOC Approx. 300 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Thinning ratio: 0 - 5%.
Convention Air spray
Not recommended.
Brush Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%
Roller Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 60 min at 25

PRODUCT DATA SHEET

Sam Tankguard Epoxy 70 Plus

A high-build, Two-component, Phenolic Polyamine-cured epoxy coat with excellent
anticorrosive and chemical resistance properties.


Characteristics
• Excellent abrasion and impact resistance.
• Excellent Chemical resistance against Acidic and alkali media.
• Designed to be used in Tank lining in oil& gas and fertilizers plants.
• Designed to be used in carbon steel and stainless-steel substrates.
• Excellent hydrocarbon and fuel resistance.
• Designed to Resist dry heat up to 200C°.
• Designed to be used under Insulation.
• Compatible with well-designed cathodic protection system.


Physical properties.
Colour Grey, (specific colours)
Texture Egg shell


Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.4 g/ml
Volume solids 70±2% Tested acc. ASTM D 2369
VOC Approx. 280 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Thinning ratio: 0 - 5%.
Convention Air spray
Not recommended.
Brush Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%
Roller Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 90 min at 25 Cº

PRODUCT DATA SHEET

Sam Tankguard Epoxy 80

A high-build, Two-component, Phenolic Polyamine -cured epoxy coat with excellent anticorrosive and
chemical resistance properties.


Characteristics
• Excellent abrasion and impact resistance.
• Excellent Chemical resistance against Acidic and alkali media.
• Designed to be used in Tank lining in oil& gas and fertilizers plants.
• Excellent hydrocarbon and fuel resistance.
• Certified jet fuel resistance and comply with EI 1541 2.2 Standard
• Certified To be used in Crude Oil and Ballast tanks.
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with well-designed cathodic protection system.


Physical properties.
Colour Grey, (specific colours)
Texture Egg shell


Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.45 g/ml
Volume solids 80±2% Tested acc. ASTM D 2369
VOC Approx. 200 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Thinning ratio: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%
Roller Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº

PRODUCT DATA SHEET