Mastic And Highbuild
Sam Epoxy mastic 80 GF
A high-build, Two-component, Polyamine-cured epoxy coat with excellent anticorrosive properties,
pigmented with glass flakes.
Characteristics
• Excellent abrasion and impact resistance.
• Excellent anti corrosion properties due to Glass Flakes Pigments.
• Used for new construction and maintenance applications
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Gray, (other colors available on request)
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.4 g/ml
Volume solids 80±2% Tested acc. ASTM D 2369
VOC Approx. 160 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 300 µm ASTM D1186
Wet film thickness per coat (µm) 125 – 375 µm ASTM D1212
Theoretical spreading rate (m2/L) 8 - 2.6 m²/L
Sam Glass Flake Epoxy Coat 90
A high-build, Two-component, Polyamine-cured epoxy coat with excellent anticorrosive properties,
pigmented with glass flakes.
Characteristics
• Excellent abrasion and impact resistance.
• Excellent anti corrosion properties due to Glass Flakes Pigments.
• Excellent chemical resistance.
• Designed to be used in Tank lining in oil& gas and fertilizers plants.
• Designed to be used in splash zones and offshore.
• Designed to be used in marine and Industrial areas.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Gray, (other colors available on request)
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.4 g/ml
Volume solids 90±2% Tested acc. ASTM D 2369
VOC Approx. 110 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 200 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 150 – 450 µm ASTM D1186
Wet film thickness per coat (µm) 166 – 500 µm ASTM D1212
Theoretical spreading rate (m2/L) 6 – 2 m²/L
Sam mastic 70
A high-build, Two-component, polyamide-cured epoxy coat with excellent anticorrosive properties.
Characteristics
• Good abrasion and impact resistance.
• Designed for new construction and maintenance applications
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Gray, (other colors available on request)
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 80 / 20
Specific gravity Approx. 1.35 g/ml
Volume solids 70±2% Tested acc. ASTM D 2369
VOC Approx. 290 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 200 µm ASTM D1186
Wet film thickness per coat (µm) 143 – 285 µm ASTM D1212
Theoretical spreading rate (m2/L) 7 - 3.5 m²/L
Sam mastic 75
A high-build, Two-component, polyamide-cured epoxy coat with excellent anticorrosive properties.
Characteristics
• Good abrasion and impact resistance.
• Designed for new construction and maintenance applications
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Gray, (other colors available on request)
Texture Semi-gloss
Mixing and Application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 80 / 20
Specific gravity Approx. 1.35 g/ml
Volume solids 75±2% Tested acc. ASTM D 2369
VOC Approx. 280 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 200 µm ASTM D1186
Wet film thickness per coat (µm) 133 – 266 µm ASTM D1212
Theoretical spreading rate (m2/L) 7.5 - 3.75 m²/L
Sam mastic 80
A high-build, Two-component, Polyamine-cured epoxy coat with excellent anticorrosive properties.
Characteristics
• Good abrasion and impact resistance.
• Used for new construction and maintenance applications
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Gray, (other colors available on request)
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.45 g/ml
Volume solids 80±2% Tested acc. ASTM D 2369
VOC Approx. 194 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 60 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 300 µm ASTM D1186
Wet film thickness per coat (µm) 125 – 375 µm ASTM D1212
Theoretical spreading rate (m2/L) 8 - 2.6 m²/L
Sam mastic Alu 80
A high-build, Two-component, Polyamine-cured epoxy coat with excellent anticorrosive properties.
Characteristics
• Excellent abrasion and impact resistance.
• Excellent anti corrosion properties due to aluminum Pigments.
• Designed for new construction and maintenance applications
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Silvergrey
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.45 g/ml
Volume solids 80±2% Tested acc. ASTM D 2369
VOC (Supplied) Approx. 150 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 300 µm ASTM D1186
Wet film thickness per coat (µm) 125 – 375 µm ASTM D1212
Theoretical spreading rate (m2/L) 8 - 2.6 m²/L
Sam mastic Alu 90
A high-build, Two-component, Polyamine-cured epoxy coat with excellent anticorrosive properties.
Characteristics
• Excellent abrasion and impact resistance.
• Excellent anti corrosion properties due to aluminum Pigments.
• Designed for new construction and maintenance applications
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Silver grey
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.45 g/ml
Volume solids 90±2% Tested acc. ASTM D 2369
VOC Approx. 130 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 300 µm ASTM D1186
Wet film thickness per coat (µm) 111 – 333 µm ASTM D1212
Theoretical spreading rate (m2/L) 9 - 3 m²/L
Sam mastic Fast dry 70
A high-build, Two-component, polyamide-cured epoxy, Fast cure with excellent anticorrosive
properties.
Characteristics
• Good abrasion and impact resistance.
• Designed for new construction and maintenance applications.
• Excellent anti corrosion properties due to pigmentation by zinc phosphate.
• Surface tolerant and good adhesion to St3 prepared steel substrates.
• Designed for Quick production conditions due to its fast drying and curing
properties.
• Compatible with most aged coatings with Excellent workability.
• Can be used with water jetting surface preparation.
Physical properties.
Colour Gray, (other colors available on request)
Texture Semi-gloss
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 80 / 20
Specific gravity Approx. 1.45 g/ml
Volume solids 70±2% Tested acc. ASTM D 2369
VOC Approx. 290 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 120 min at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 200 µm ASTM D1186
Wet film thickness per coat (µm) 143 – 285 µm ASTM D1212
Theoretical spreading rate (m2/L) 7 - 3.5 m²/L
Sam MIO Epoxy Coat 80
A high-build, Two-component, Polyamide-cured epoxy Pigmented With micaceous iron oxide.
Characteristics
• Excellent abrasion and impact resistance.
• Excellent anti corrosion properties with excellent workability.
• Excellent water and chemical resistance due to MIO Pigments properties.
• Design to be used as a mid-coat or finish-coat in Samco Epoxy systems.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Silvergrey
Texture Flat
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 80 / 20
Specific gravity Approx. 1.8 g/ml
Volume solids 80±2% Tested acc. ASTM D 2369
VOC Approx. 180 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 2 Hours at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 300 µm ASTM D1186
Wet film thickness per coat (µm) 125 – 375 µm ASTM D1212
Theoretical spreading rate (m2/L) 8 – 2.6 m²/L
Sam MIO Epoxy Primer 65
A high-build, Two-component, Polyamide-cured epoxy Pigmented With micaceous iron oxide.
Characteristics
• Good abrasion and impact resistance.
• Excellent anti corrosion properties with excellent workability.
• Excellent water and chemical resistance due to MIO Pigments properties.
• Design to be used as a primer or a mid-coat in Samco Epoxy systems.
• Can be used with water jetting surface preparation.
• Compatible with well-designed cathodic protection system.
Physical properties.
Colour Silvergrey
Texture Flat
Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 80 / 20
Specific gravity Approx. 1.5 g/ml
Volume solids 65±2% Tested acc. ASTM D 2369
VOC Approx. 300 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Volume of thinner: 0 - 5%.
Convention Air spray
Volume of thinner: 0 - 10%.
Brush Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%
Roller Suitable for stripe coat and touch up.
Volume of thinner: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 3 Hours at 25 Cº
Recommended film thickness range
Dry film thickness per coat (µm) 100 – 200 µm ASTM D1186
Wet film thickness per coat (µm) 154 – 307 µm ASTM D1212
Theoretical spreading rate (m2/L) 6.5 – 3.25 m²/L
