Heat Resistance

Sam Coat HR 200

A single pack, aluminum based, modified alkyd, resist dry heat up to 200C°.

Characteristics
• Good abrasion and impact resistance.
• Dry Heat resistance up to 200C°
• Designed for Oil& gas, Energy plants, Industrial environment.
• Excellent workability.

Physical properties.
Colour Silver
Texture Gloss

Mixing and application Information
Number of components One
Specific gravity Approx. 1 g/ml
Volume solids 35±2% Tested acc. ASTM D 2369
VOC Approx. 500 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 120 -150 bar. Nozzle size: 0.38 - 0.53 mm.
Spray angle: 40 - 80 degrees.
Thinner Ratio: 0 - 5%.
Convention Air spray
Thinner Ratio: 0 - 10%.
Brush Suitable.
Thinner Ratio: 0 - 10%
Roller Suitable.
Thinner Ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 4

Recommended film thickness range
Dry film thickness per coat (µm) 30 – 50 µm ASTM D1186
Wet film thickness per coat (µm) 85 – 143 µm ASTM D1212
Theoretical spreading rate (m2/L) 11.6 – 7 m²/L

PRODUCT DATA SHEET

Sam Coat HR 250

A single pack, silicone acrylic top coat, resist dry heat up to 250C°.

Characteristics
• Good abrasion and impact resistance.
• Dry Heat resistance up to 250C°
• Designed for Oil& gas, Energy plants, Industrial environment.
• Can be applied over SAMCO Ethyl zinc silicates primers.
• Excellent workability.

Physical properties.
Colour Aluminum, Specific colours
Texture Semi-gloss

Mixing and application Information
Number of components One
Specific gravity Approx. 1.1 g/ml
Volume solids 35±2% Tested acc. ASTM D 2369
VOC Approx. 500 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 120 -150 bar. Nozzle size: 0.38 - 0.53 mm.
Spray angle: 40 - 80 degrees.
Thinner Ratio: 0 - 5%.
Convention Air spray
Thinner Ratio: 0 - 10%.
Brush Suitable.
Thinner Ratio: 0 - 10%
Roller Suitable.
Thinner Ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 3

Recommended film thickness range
Dry film thickness per coat (µm) 20 – 40 µm ASTM D1186
Wet film thickness per coat (µm) 57 – 114 µm ASTM D1212
Theoretical spreading rate (m2/L) 17.5 – 8.75 m²/L

PRODUCT DATA SHEET

Sam Coat HR 600

A single pack, silicone based top coat, resist dry heat up to 600C°.

Characteristics
• Good abrasion and impact resistance.
• Dry Heat resistance up to 600C°
• Designed for Oil& gas, Energy plants, Industrial environment.
• Can be applied over SAMCO Ethyl zinc silicates primers.
• Excellent workability.

Physical properties.
Colour Aluminum
Texture Gloss

Mixing and application Information
Number of components One
Specific gravity Approx. 1.1 g/ml
Volume solids 40±2% Tested acc. ASTM D 2369
VOC Approx. 500 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 120 -150 bar. Nozzle size: 0.38 - 0.53 mm.
Spray angle: 40 - 80 degrees.
Thinner Ratio: 0 - 5%.
Convention Air spray
Thinner Ratio: 0 - 10%.
Brush Suitable.
Thinner Ratio: 0 - 10%
Roller Suitable.
Thinner Ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 3

Recommended film thickness range
Dry film thickness per coat (µm) 20 – 40 µm ASTM D1186
Wet film thickness per coat (µm) 50 – 100 µm ASTM D1212
Theoretical spreading rate (m2/L) 20 – 10 m²/L

PRODUCT DATA SHEET

Sam Tankguard Epoxy 65

A high-build, Two-component, Phenolic Polyamine-cured epoxy coat with excellent
anticorrosive and chemical resistance properties.

Characteristics
• Excellent abrasion and impact resistance.
• Excellent Chemical resistance against Acidic and alkali media.
• Designed to be used in Tank lining in oil& gas and fertilizers plants.
• Excellent hydrocarbon and fuel resistance.
• Designed to Resist dry heat up to 200C°
• Designed to be used under Insulation.
• Compatible with well-designed cathodic protection system.

Physical properties.
Colour Grey, (specific colours)
Texture Egg shell

Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.3 g/ml
Volume solids 65±2% Tested acc. ASTM D 2369
VOC Approx. 300 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Thinning ratio: 0 - 5%.
Convention Air spray
Not recommended.
Brush Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%
Roller Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 60 min at 25 Cº

PRODUCT DATA SHEET

Sam Tankguard Epoxy 70 Plus

A high-build, Two-component, Phenolic Polyamine-cured epoxy coat with excellent
anticorrosive and chemical resistance properties.

Characteristics
• Excellent abrasion and impact resistance.
• Excellent Chemical resistance against Acidic and alkali media.
• Designed to be used in Tank lining in oil& gas and fertilizers plants.
• Designed to be used in carbon steel and stainless-steel substrates.
• Excellent hydrocarbon and fuel resistance.
• Designed to Resist dry heat up to 200C°.
• Designed to be used under Insulation.
• Compatible with well-designed cathodic protection system.

Physical properties.
Colour Grey, (specific colours)
Texture Egg shell

Mixing and application Information
Number of components Two
Mixing ratio By Volume, base to hardener: 75 / 25
Specific gravity Approx. 1.4 g/ml
Volume solids 70±2% Tested acc. ASTM D 2369
VOC Approx. 280 g/liter
Flashpoint >25°C
spray Airless spray Recommended
Pressure at nozzle: 180 - 250 bar. Nozzle size: 0.41 - 0.58 mm.
Spray angle: 40 - 80 degrees.
Thinning ratio: 0 - 5%.
Convention Air spray
Not recommended.
Brush Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%
Roller Suitable for stripe coat and touch up.
Thinning ratio: 0 - 10%.
Thinner/Cleaner SAM Thinner No. 1
Thinning should only be added after the two components have
been thoroughly mixed.
Pot life 90 min at 25 Cº